BURKERT 134248 (Type 6013) is a direct-acting and compact 2/2-way plunger valve up to DN 6.0. The stopper and the core guide tube are welded together to increase pressure resistance and leak-tightness. A variety of seal material combinations are available to suit different applications. A Bürkert-specific flange variant (SFB) enables the space-saving arrangement of valves on a multiple manifold. Kick and drop coils are available to reduce electrical power consumption during operation.

General Technical Data

Standard Variant

Product properties	Description
Material
Seal	FKM, PTFE/Graphite (EPDM on request)
Body	Brass, stainless steel 1.4305/303
Coil	Polyamide, epoxy
Orifice	DN 2.0...DN 6.0
Circuit function	A and B
Thermal insulation class of solenoid coil	Polyamide coil class B, Epoxy coil class H
Performance data
Duty cycle/single valve with block assembly on manifold	100% continuous operation. Intermittent operation 60% (30 min) or with 5 W coil (on request)
Electrical data
Operating voltage	24 V DC, 24 V 50 Hz, 24 V 60 Hz, 120 V 50 Hz, 230 V 50 Hz, 240 V 60 Hz
Voltage tolerance	±10%
Medium data
Operating medium	Technical vacuum, neutral gases and liquids (e.g. compressed air, water, hydraulic oil)
Medium temperature (With FKM)	-10 °C...+100 °C (PA coil), -10 °C...+120 °C (Epoxy coil), -40 °C on request
Medium temperature (With PTFE/Graphite)	-40 °C...+180 °C
Medium temperature (With FKM, circuit function B)	-10 °C...+100 °C (AC), -10 °C...+120 °C (DC)
Viscosity	Max. 21 mm²/s
Product connections
Electrical connection	Plug contacts according to DIN EN 175 301 - 803 form A for cable plug Type 2518 or Type 2509. ATEX/IECEx variant with 3 m moulded cable or terminal cable
Port connection	G 1/8, G 1/4, G 3/8, NPT 1/8, NPT 1/4, NPT 3/8, manifold (SFB)
Approvals and conformities
Degree of protection	IP65 with cable plug
Environment and installation
Installation position	As required, preferably with actuator upright
Ambient temperature	Max. +55 °C (higher temperatures on request)

Analytical Variant

This variant is particularly suitable for switching from extremely pure gaseous medium. All medium-affected parts are submitted to additional purification processes, so that the medium is not contaminated under any circumstances. The tightness test takes place at the Helium leak detector from a min. of 10⁻⁴ mbar l/sec.

Product properties	Description
Material
Seal	Silicon, oil and fat free variant. Tightness < 10⁻⁴ mbar l/s
Body	Brass, stainless steel 1.4305/303
Medium data
Operating medium	Neutral medium, which does not attack the body and seal materials
Environment and installation
Installation instructions	No oils, fats or silicone to be used during installation.

DVGW Variant

The solenoid valve Type 6013 DVGW is primarily intended as an automatic safety shut-off valve for fuel gases. A strainer is installed in the inlet of the valve.

Product properties	Description
Material
Seal	NBR
Body	Brass, stainless steel 1.4305/303
Circuit function	A
Performance data
Operating pressure	Max. 0...5 bar
Medium data
Operating medium	Fuel gases (e.g. town gas, district gas, liquid gas)
Medium temperature	-20 °C...+80 °C
Approvals and conformities
Standards	DIN EN 161:2013, DIN EN 13611:2016
Environment and installation
Ambient temperature	-20 °C...+55 °C

Circuit Functions

Circuit Function	Description
A (CF A)	2/2-way solenoid valve, Direct-acting, Normally closed
B (CF B)	2/2-way solenoid valve, Direct-acting, Normally open

Approvals and Conformities

General Notes

The approvals and conformities listed below must be stated when making enquiries. This is the only way to ensure that the product complies with all required specifications. Not all available variants can be supplied with the below mentioned approvals or conformities.

Explosion Protection

Approval	Description
ATEX / IECEx (Category 2)	Optional: Explosion protection according to category 2 (zone 1/21). Coils with cable outlet: ATEX: EPS 18 ATEX 1232 X II 2G Ex mb IIC T4 Gb, II 2D Ex mb IIIC T130 °C Db IECEx: IECEx EPS 18.0110 X Ex mb IIC T4 Gb, Ex mb IIIC T130 °C Db Coils with terminal box: ATEX: EPS 18 ATEX 1232 X II 2G Ex eb mb IIC T4 Gb, II 2D Ex mb tb IIIC T130 °C Db IECEx: IECEx EPS 18.0110 X Ex eb mb IIC T4 Gb, Ex mb tb IIIC T130 °C Db
ATEX / IECEx (Category 3)	Optional: Explosion protection according to category 3 (zone 2/22). Coil with plug contacts form A and cable plug Type 2509: ATEX: EPS 18 ATEX 1232 X II 2G Ex mb IIC T4 Gb, II 2D Ex mb IIIC T130 °C Db IECEx: IECEx EPS 18.0110 X Ex mb IIC T4 Gb, Ex mb IIIC T130 °C Db

North America (USA/Canada)

Approval	Description
UL Listed	Optional: UL Listed for the USA (valid for valves) according to UL 429 (electrically operated valves)
UL Hazardous Locations	Optional: UL Hazardous Locations – Explosion Protection (valid for coils). UL Listed for Hazardous Locations for USA and Canada: Class I, Zone 1; Class I, Division 2, Group A, B, C and D; Class II + III, Division 2, Group F and G
UL Recognized	Optional: UL Recognized for the USA (valid for valves) according to UL 429
CSA	Optional: CSA for Canada (valid for valves) according to CSA 139
FM (Factory Mutual)	Optional: FM (Factory Mutual) – Explosion Protection (valid for coils). FM for Hazardous Locations for USA and Canada: Class I, Zone 1; Class I, Division 1, Groups A, B, C and D; Class II + III, Division 1, Groups E, F and G

Drinking Water & Hygiene

Conformity	Description
Drinking Water	Suitable for use in drinking water applications. The materials comply with the assessment principles (UBA) for materials in contact with drinking water (TrinkwasserV). PA body (PF36): Suitable for products with a maximum temperature of + 60 °C (warm water). PPS/brass/stainless steel body (PF39): Suitable for products with a maximum temperature of + 85 °C (hot water).
FDA	FDA – Code of Federal Regulations (valid for the variable code PL02, PL03). All wetted materials are compliant with the Code of Federal Regulations published by the FDA.
USP	United States Pharmacopeial Convention (USP) (valid for the variable code PL04). All wetted materials are biocompatible.
EC 1935/2004	EC Regulation 1935/2004 of the European Parliament and of the Council (valid for the variable code PL01, PL02).

Materials

Standard Variant

No.	Element	Material
1	Stopper	Stainless steel 1.4105/430F
2	Shading ring	Cu (brass variant), Ag (stainless steel variant)
3	Spring	Stainless steel 1.4310/301
4	Magnetic core	Stainless steel 1.4105/430F
5	Core guide tube	Stainless steel 1.4303/305/308
6	Seal	FKM, Graphite (high temperature variant)
7	Armature seal	FKM, PTFE
8	Valve body	Brass, Stainless steel 1.4305/303
9	Sub-base	Steel, surface finish thick-film passivated (brass variant), Stainless steel 1.4301/304 (stainless steel variant)
10	Cover	Polyamide
11	Coil	PA (polyamide), Epoxy
12	Nut	Steel, surface finish thick-film passivated (brass variant), Stainless steel 1.4305/303 PTFE coated (stainless steel variant)

ATEX/IECEx Cable Variant

No.	Element	Material
1	Nut	Steel, surface finish thick-film passivated (brass variant), Stainless steel 1.4305/303 PTFE coated (stainless steel variant)
2	Stopper	Stainless steel 1.4105/430F
3	Shading ring	Cu (brass variant), Ag (stainless steel variant)
4	Spring	Stainless steel 1.4310/301
5	Magnetic core	Stainless steel 1.4105/430F
6	Core guide tube	Stainless steel 1.4303/305/308
7	Seal	FKM, Graphite (high temperature variant)
8	Armature seal	FKM, PTFE (high temperature variant)
9	Valve body	Brass, Stainless steel 1.4305/303
10	Sub-base	Steel, surface finish thick-film passivated (brass variant), Stainless steel 1.4301/304 (stainless steel variant)
11	Cover	Polyamide
12	Coil	Epoxy

ATEX/IECEx Terminal Box Variant

No.	Element	Material
1	Terminal box	Aluminium
2	Nut	Steel, surface finish thick-film passivated (brass variant), Stainless steel 1.4305/303 PTFE coated (stainless steel variant)
3	Stopper	Stainless steel 1.4105/430F
4	Coil	Epoxy
5	Shading ring	Cu (brass variant), Ag (stainless steel variant)
6	Spring	Stainless steel 1.4310/301
7	Magnetic core	Stainless steel 1.4105/430F
8	Core guide tube	Stainless steel 1.4303/305/308
9	Cover	Polyamide
10	Sub-base	Steel, surface finish thick-film passivated (brass variant), Stainless steel 1.4301/304 (stainless steel variant)
11	Seal	FKM, Graphite (high temperature variant)
12	Armature seal	FKM, PTFE (high temperature variant)
13	Valve body	Brass, Stainless steel 1.4305/303

Dimensions

Standard Variant

INFO

Dimensions in mm.

Port connection	A [inch]	B [mm]	C [mm]	D [mm]	G [mm]
Thread	G/NPT 1/8	32	20.8	32.6	8
Thread	G/NPT 1/4	46	26.8	49	12
Thread	G/NPT 3/8	50	39.8	38	12
Flange	-	32	14.3	32.6	-

Coil size	E [mm]	F [mm]
5	32	45
6	40	51

ATEX/IECEx Cable Variant

INFO

Dimensions in mm.

Port connection	A [inch]	B [mm]	C [mm]	D [mm]	G [mm]
Thread	G/NPT 1/8	32	20.8	32.6	8
Thread	G/NPT 1/4	46	26.8	49	12
Thread	G/NPT 3/8	50	39.8	38	12
Flange	-	32	14.3	32.6	-

Coil size	E [mm]	F [mm]
5	32	46
6	40	52

ATEX/IECEx Terminal Box Variant

INFO

Dimensions in mm.

Port Connection	A [inch]	B [mm]	C [mm]	D [mm]	H [mm]
Thread	G/NPT 1/8	32	20.8	32.6	8
Thread	G/NPT 1/4	46	26.8	49	12
Thread	G/NPT 3/8	50	39.8	38	12
Flange	-	32	14.3	32.6	-

Coil size	E [mm]	F [mm]
5	32	44
6	40	51

Performance Specifications

Power Consumption

Circuit function A

Orifice [mm]	Power consumption	Inrush AC [VA]	Hold AC [VA]	Coil size	Opening [ms]	Closing [ms]
2.0	8 W AC or 8 W DC (9)	24	17	5 (32 mm)	20	30
2.5	8 W AC or 8 W DC (9)	24	17	5 (32 mm)	20	30
3.0	8 W AC or 8 W DC (9)	24	17	5 (32 mm)	20	30
3.0	10 W AC or 10 W DC (11)	30	22	6 (40 mm)	20	30
4.0	8 W AC or 8 W DC (9)	24	17	5 (32 mm)	20	30
4.0	10 W AC or 10 W DC (11)	30	22	6 (40 mm)	20	30
6.0	8 W AC or 8 W DC (9)	24	17	5 (32 mm)	20	30
6.0	10 W AC or 10 W DC (11)	30	22	6 (40 mm)	20	30

(The values in brackets correspond to a coil temperature of + 20 °C.)

Circuit function B

Orifice [mm]	Power consumption	Inrush AC [VA]	Hold AC [VA]	Coil size	Opening [ms]	Closing [ms]
2.00	7 W AC or 8 W DC (9)	24	17	5 (32 mm)	20	30
3.00	7 W AC or 8 W DC (9)	24	17	5 (32 mm)	20	30
4.00	7 W AC or 8 W DC (9)	24	17	5 (32 mm)	20	30
6.00	7 W AC or 8 W DC (9)	24	17	5 (32 mm)	20	30

(The values in brackets correspond to a coil temperature of + 20 °C.)

Product Installation

Installation Notes

Control for impulse variant with polarity reversal control

Use cable plug without electrical wiring exclusively for impulse variant. Pulse duration min. 50 ms.

Polarity (is marked on the coil with a label)	Features	Terminal connections
- switch ON +	valve open	(+) on terminal 2 and (-) on terminal 1
+ switch OFF -	valve closed	(+) on terminal 1 and (-) on terminal 2