Skip to content
REV316.5 mm Station Width4x 3/2-Way CF CG 3/8 SupplyPush-in D8ATEX / IECExEx ia IIC T6IP20

BURKERT 20051376 Type 8640 4-Bank Pneumatic Valve Block, 16.5 mm, 4x 3/2-Way CF C

BURKERT 20051376 (Type 8640) is a REV3 4-bank pneumatic valve block featuring 16.5 mm station width, 4x 3/2-way normally closed valves, G 3/8 supply, D8 push-in ports, and ATEX/IECEx Ex ia IIC T6 certification.

BURKERT 20051376 Type 8640 4-Bank Pneumatic Valve Block, 16.5 mm, 4x 3/2-Way CF C

BURKERT 20051376 (Type 8640) is a 4-bank pneumatic valve block engineered on the Revision 3 (REV3) modular architecture. It is factory-configured with four servo-controlled 3/2-way solenoid valves operating under circuit function C (normally closed). Built with a 16.5 mm station width per valve position, this unit integrates common pneumatic supply ports G 3/8 and downward-facing D8 push-in working connections directly on the pneumatic base module. The block operates without an internal fieldbus communication module, utilizing individual single wiring connections.

Designed for demanding industrial and hazardous environments, article 20051376 delivers an air flow rate of 700 l/min per station under standard reference conditions. The valve island block provides an operating pressure range from 2.00 bar to 8.00 bar, operates at 24 V DC with an energy-efficient 1 W nominal coil power rating, and carries hazardous area certifications under ATEX and IECEx for II 2 G Ex ia IIC T6 classification.

Technical Specifications ​

ParameterSpecification
Article Number20051376
Valve Island SystemType 8640
Generation / RevisionRevision 3 (REV3)
Configuration4-bank valve block (04-bank)
Width per Station16.5 mm
Valve Function4x 3/2-way valve function C (servo-controlled, normally closed)
Manual OverrideStandard manual override integrated on each valve
Supply Port 1 (P), Exhaust Ports 3 (R), 5 (S)G 3/8
Working Port 2 (A), 4 (B)D8 push-in coupling (bottom pneumatic module orientation)
Operating Pressure Range2.00 bar to 8.00 bar
Auxiliary Pilot Air Requirement> 2 bar (when external supply air is configured)
Flow Rate QNn Air700 l/min (measured at +20 °C, 6 bar inlet pressure, 1 bar differential)
Medium Temperature Range0 °C to 50 °C
Ambient Temperature Range0 °C to 55 °C
Operating MediumOil-free or lubricated compressed dry air, neutral gases (5 µm filtering)
Compressed Air Quality ClassISO 8573-1: 2010, Class 7.4.4
Nominal Operating Voltage24 V DC (±10% voltage tolerance, residual ripple 1 Vss)
Nominal Power per Valve1 W
Operating Duty Cycle100% continuous operation (ED)
Electrical Connection TypeSingle wiring (without internal bus communication, 0 digital inputs)
Installation MountingStandard DIN rail EN 50022 (35 x 7.5 mm or 35 x 15 mm)
Valve Body MaterialPolyamide (PA) / Aluminium
Sealing MaterialNBR
Ingress Protection RatingIP20 (protection class III according to VDE 0580)
Explosion Protection ApprovalsZ003 ATEX, Z004 IECEx
Explosion Protection MarkingII 2 G Ex ia IIC T6, Ex ia IIC T6

Revision 3 Architecture and Station Characteristics ​

BURKERT 20051376 Type 8640 REV3 16 mm station design with blue release rings

The Type 8640 REV3 platform introduces optimized mechanical and pneumatic features over earlier REV1 and REV2 revisions. For 16 mm station blocks, the REV3 generation features a wavy channel arrangement for the working connections, blue release rings on the push-in tube connectors, and a standardized valve flange interface.

Revision 3 Efficiency

Revision 3 pneumatic modules limit the pressure drop across integrated P-shut-off elements to a maximum flow reduction of 20%, whereas earlier revisions experienced up to 50% flow reduction.

Circuit Function and Valve Operation ​

BURKERT 20051376 Type 8640 circuit function C 3/2-way normally closed pneumatic symbol

Article 20051376 is equipped with four 3/2-way servo-controlled valves configured in Circuit Function C. In the de-energized rest position, pressure supply port 1 (P) is closed, while working port 2 (A) exhausts to port 3 (R). Upon electrical energization, the pilot rocker mechanism shifts, opening supply port 1 to working port 2 and sealing exhaust port 3.

Each valve station includes a manual override that allows manual commissioning and testing without electrical excitation. To activate the manual override, press and rotate the mechanism 90° clockwise until it locks. It does not automatically reset and must be manually restored to zero position before resuming normal electrical control.

Operational StageResponse Time
Opening Time (Switching On)20 ms
Closing Time (Switching Off)12 ms to 17 ms
Nominal Valve Power1 W (24 V DC)
Standard Coil Connection InterfaceTag connector DIN EN 175301-803 Form C

Dimensions and DIN-Rail Mounting ​

BURKERT 20051376 Type 8640 16 mm station width dimensional drawing for EN 50022 DIN rail

The valve block is pre-configured for DIN rail mounting according to standard rail EN 50022 (35 x 7.5 mm or 35 x 15 mm). Installation is carried out by engaging the upper hook groove of the modular block onto the top edge of the DIN rail, pressing the lower clamping pieces into place, and securing them with the clamping screws.

Installation position is arbitrary, with the preferred orientation having the solenoid actuators positioned upright. Single valves mounted onto base modules are fastened using two M3 x 30 mm screws tightened to the recommended mounting torque of 0.6 ±0.1 Nm.

Pneumatic Block Assembly and Piping ​

BURKERT 20051376 Type 8640 16 mm pneumatic block assembly structure

The modular pneumatic section is constructed from high-quality polyamide (PA) elements joined by integrated snap hooks and sealed by elastomeric O-rings:

  1. Left pneumatic connection module with main supply port G 3/8
  2. Basic pneumatic 4-fold module (16 mm width per station) with bottom-oriented D8 push-in connections
  3. Right pneumatic connection module with exhaust port G 3/8
  4. Solenoid valves (Type 6526 3/2-way, 16.5 mm width)

Push-In Hose Connection Guidelines (ISO 14743)

To prevent connection leakage and ensure full holding capability:

  • Use hose lines with minimum hardness of 40 Shore D conforming to DIN 73378.
  • Ensure tube ends are cut straight at right angles without burrs or external surface scoring.
  • For 8 mm outside diameter (OD) hoses, verify tube dimensional tolerances: PA tubing must remain within ±0.08 mm; PU tubing must remain within ±0.10 mm.
  • Verify holding capacity against the standard minimum tensile forces: 170 N for Polyamide (PA) and 150 N for Polyurethane (PU).

Operating Pressure Limits

The differential pressure between supply port 1 and exhaust port 3 must be at least 2 bar. If the system operating temperature drops below 0 °C, operation must be restricted strictly to dried compressed air to prevent internal freezing.

Explosion Protection and Regulatory Approvals ​

Article 20051376 satisfies European and international safety requirements for equipment deployed in potentially explosive gas atmospheres. The unit holds certification approvals:

  • ATEX Approval Type: Z003 ATEX
  • IECEx Approval Type: Z004 IECEx
  • Marking: II 2 G Ex ia IIC T6, Ex ia IIC T6

When installed in an industrial control cabinet, the system provides ingress protection IP20. In fully closed enclosures meeting appropriate housing standards, protection levels up to IP65 can be maintained.

Spare Parts and Replacement Components ​

BURKERT 20051376 Type 8640 REV3 16 mm pneumatic spare parts exploded view

Maintenance and modular expansion of the Type 8640 REV3 16 mm system utilize standardized Bürkert components:

PositionDescriptionSpecification / ContentArticle No.
1Replacement 3/2-way valve (CF C)Type 6526, 2.0-8.0 bar, 24 V DC, 1 W156840 / 158947
2Cover plateCover plate for Type 6526 / 6527 valve slot653765
-Electrical connection coverCover plate for electrical connection 6526/6527657519
3Valve seal kitFM17 spare valve seals (pack of 12)20016307
4Module seal kitMP17 spare module seals (pack of 4)20016310
5Left supply unitType 8640, 16 mm, G 3/8 connection20042793
5Right supply unitType 8640, 16 mm, G 3/8 connection20042796
6Base module 4-foldBase unit Type 8640, 16 mm, 4-fold, D8, FM1720042790
6Base module 4-fold with check valveBase unit Type 8640, 16 mm, 4-fold, D8, FM17, RSV20042792